FTTX Demo Tutorial

Fiber network

Fiber cables

Draw cable routes, record them by walking with GPS, track used cores and review field submissions.

Who can use it: Super Admin, NOC Admin, Field Technician, Employee Open this page in the app
On this page

What this page is for #

Every fiber cable between two sites: its route on the map, its length, how many cores it has and which are in use. Field staff can record a route by simply walking it with a phone; a senior then reviews and approves it.

Fiber cables
Fiber cables (example with sample data)
  1. 1 Tabs: all cables, routes pending review, rejected routes, and your own drafts.
  2. 2 Cores used out of the total.
  3. 3 A route waiting for review, with who submitted it.
  4. 4 Add cable.
Sample data, not a real network. Tap a number or a line to match them; tap the picture to enlarge.

Add a cable and draw its route #

Add a fiber cable
Add a fiber cable (example with sample data)
  1. 1 Record my walk adds points from your phone’s GPS while you follow the cable. “Add my position” adds one point.
  2. 2 Undo / Clear the last point or the whole route.
  3. 3 Full screen for a large map.
  4. 4 The map: tap a site pin to start, then tap along the route. Drag a point to adjust it; long-press or right-click a point to remove it.
  5. 5 Starts at / Ends at: the route snaps to these sites.
Sample data, not a real network. Tap a number or a line to match them; tap the picture to enlarge.
Draw a route on the computer
  1. Press Add cable.
  2. Enter the Name, the number of Cores and the Cable type (Aerial, ADSS, Underground, Duct, Drop).
  3. Choose Starts at and Ends at.
  4. On the map, tap along the real path of the cable, pole by pole.
  5. Leave Length in metres empty to use the drawn length, or type the measured length.
  6. Press Save cable.
Record a route by walking it

Needs: Field Technician · Employee

  1. On your phone, open Fiber cables → Add cable and fill in the name and cores.
  2. Choose the start site. Stand there and press Record my walk. Allow the browser to use your location.
  3. Walk along the cable with the screen on. A point is added every few metres; poor GPS readings are skipped.
  4. At the end, stop recording, choose the end site and press Submit for review.

Review of submitted routes #

Routes from field staff are drafts until approved. Until then they appear as dashed orange lines on the map and are not counted in the totals.

A submitted route, opened for editing
A submitted route, opened for editing (example with sample data)
  1. 1 Banner: who submitted it and when. The recorded walk stays visible in grey while you adjust the blue route.
  2. 2 The submitter can continue recording their own draft.
Sample data, not a real network. Tap a number or a line to match them; tap the picture to enlarge.
Reviewing a route
Reviewing a route (example with sample data)
  1. 1 Note to the submitter: required when you reject.
  2. 2 Approve as recorded accepts the route as it is. “Adjust, then approve” opens the editor first.
  3. 3 Reject sends it back with your note.
Sample data, not a real network. Tap a number or a line to match them; tap the picture to enlarge.
Approve or reject a route

Needs: NOC Admin

  1. Open the tab Pending review and tap the cable.
  2. Compare the route with what you know of the ground.
  3. Press Approve as recorded; or Adjust, then approve, correct the points and press Save & approve; or write a note and press Reject.
My route was rejected

Needs: Field Technician · Employee

  1. Open the tab Rejected (or My drafts) and read the reviewer's note.
  2. Open the cable, correct the route and submit it again.

Cores and their colours #

A cable's page
A cable's page (example with sample data)
  1. 1 Cores with their standard colour and tube, and what each one feeds. Free cores are marked “Free”.
  2. 2 Length and fiber loss of the cable (0.35 dB per km unless changed in the loss standards).
  3. 3 Show on map.
Sample data, not a real network. Tap a number or a line to match them; tap the picture to enlarge.

A core becomes “in use” when you choose it as the feed of a splitter on the device form. The colours follow the usual order: blue, orange, green, brown, slate, white, red, black, yellow, violet, rose, aqua; then the same again in tube 2.

Finished this topic?

Tick it off; the topic list shows what you have read.