Monitoring
Add an ONU to an OLT
Register a new ONU on a Huawei OLT from the app: scan, choose the service, review, done.
Who can use it:
Super Admin, NOC Admin
What this is for #
Some OLTs (Huawei) do not accept a new ONU by themselves: someone must register it. The Add ONU button on the OLT page does that for you. The app logs in to the OLT, registers the ONU and sets up its service, with no commands to type.
- 1 Four steps: Find → Service → Review → Done.
- 2 Two ways to find the ONU: pick it from the ones the OLT has seen, or type its serial number.
- 3 A found ONU: serial, model, the PON port it is plugged into and when the OLT saw it. Tap “Add this ONU”.
- 4 Scan again re-reads the list from the OLT, for an ONU you have just plugged in.
Add an ONU, step by step #
- Plug the ONU into the fiber and power it on.
- Open the OLT's page and press Add ONU. The app reads the OLT for a moment.
- Find. Tap Add this ONU on the right card. Not listed? Press Scan again, or switch to Type the serial number, enter the serial (16 characters, or like
HWTC-1C2E4080) and choose the PON port. - Service. Tap a Service template if one exists. Otherwise choose the Line profile, Service profile and the VLAN the customer's traffic uses. Add a description (for example the customer ID).
- Service type. Keep GEM port + LAN port VLAN unless your network team says otherwise. Choose LAN ports, untagged on OLTs where the add fails with “The GEM index does not exist”; then there is no GEM port to fill in.
- LAN ports. The VLAN is put untagged on the ONU's LAN port so an ordinary router works; LAN 1 is chosen for you. Tap the port numbers to choose others (for example 1 to 4). Without a LAN port the customer gets no internet.
- Press Review. Check the summary; the box “What runs on the OLT” shows the exact commands.
- Press Add ONU on the OLT. The wizard shows that it is working. Changes to one OLT run one at a time, so yours may wait a moment behind another; while it waits you can still Cancel.
- Done. The result tells you the ONU's ID and state. The ONU now appears in the OLT's list and a sync is queued.
What the app checks for you #
- An ONU whose serial already exists on this OLT is shown as “Already in …” and cannot be added twice.
- The ONU is saved in the app only after the OLT confirms it is registered.
- If the OLT refuses the service step, the half-added ONU is removed again, so nothing is left behind.
- After a successful add, the OLT's configuration is saved so a reboot does not lose it (an administrator can switch this off in Settings).
- Every add is written to the Activity log.
- The card OLT changes on the OLT page lists the adds and deletes that are waiting, running or finished, with their result.
If something is not right #
| You see | Do this |
|---|---|
| “No unregistered ONU right now” | Check the ONU has power and fiber, wait a few seconds, Scan again. Or type the serial to register it before it is connected. |
| “PON is not known here yet” | Sync the OLT first so the app knows that port. |
| An error about logging in | The CLI username / password on the OLT's Edit page is wrong, or the collector service is down (ask your administrator). |
| The result is a warning with commands | The ONU was registered but one step (usually the LAN port VLAN) was refused. The result lists what is still to be done on the OLT; pass it to your network engineer. |
| “The GEM index does not exist” | This OLT's line profile has no such GEM port. Add the ONU again with Service type set to LAN ports, untagged, and save it as a template for this OLT. |
| Profile lists are empty | Type the profile numbers by hand; they are the IDs configured on the OLT. |
Related topics
OLT page
One OLT in detail: sync status, CPU / memory, PON ports with laser readings and the ONU list.
Inactive ONUs & ONU Delete
ONUs that have been down for days or weeks, with a day-by-day strip, CSV export and Delete on the OLT.
ONU list
Search any ONU by serial, MAC or customer. Filter by status, power or temperature, refresh one live.
Settings
Company-wide choices: how often OLTs sync, CLI rules, ONU Add / Delete options and the sync plan.
Finished this topic?
Tick it off; the topic list shows what you have read.